Hoses & connectors: $100–$200
The brittle old flexible behind the cooktop: tiny part, outsized share of the leaks we find.
Licensed Gas Fitting
Gas Fitting
Done Right In
Kellyville
Gas does not grade on a curve. A connection is either tested and certified or it is a liability with a warranty problem, so every gas job we do across Kellyville, from a cooktop swap to a full outdoor kitchen line, ends the same way: needle steady on the manometer, appliances burning blue, paperwork done.
- Licence 368473C, fully insured
- Every job pressure-tested to AS/NZS 5601
- Smell gas now? Leave & call 131 909 first
Why The Law Keeps Gas Licensed In Kellyville
NSW reserves every gas task, down to connecting an oven, for licensed gasfitters, and the logic is unsentimental: plumbing mistakes stain ceilings, gas mistakes burn houses and poison air. The leaks we attend have a recurring origin story, and it is rarely the pipework’s idea, it is a confident DIY connection or a handyman’s thread tape, discovered later by someone’s nose.
What the licence actually buys is the ending: the whole installation held against a manometer until the needle refuses to move, every appliance checked for a clean blue burn and honest ventilation, and the work done to AS/NZS 5601, the clause your insurer reaches for when something ever goes wrong. Across Kellyville and the Hills District, no gas job of ours skips that ending.
If you smell gas in a block
The procedure does not change because you have neighbours, but the urgency does, a leak in a shared building affects everyone on that riser.
Not every street is on reticulated gas. Jemena is the largest gas distributor in NSW, supplying over 1.5 million homes and businesses, but where the main does not reach, LPG changes both the appliance and the pipe sizing.
Leave, take others with you, and call 131 909 from outside. Then notify the building manager. Do not attempt to isolate anything in a common meter room yourself; the network operator attends around the clock and that is what they are for.
Gas in an apartment: what is yours
In a block, the supply to the building and the risers are common property; the pipework and appliances inside your lot are generally yours. Individual meters may sit in a common meter room, which frequently confuses the question of access.
Establish it before arranging work. Anything on common property needs the owners corporation to authorise it, and a plumber cannot simply proceed because a resident asked.
Adding or moving gas in a strata property
Putting a gas cooktop where there was not one, or moving an appliance during a renovation, is rarely just plumbing in a block. It usually requires an owners corporation approval, sometimes a by-law, and always correct ventilation and flueing for the space.
We will tell you what the work needs before you go to the committee, so the application you submit is the one that gets approved rather than the one that comes back with questions.
Why gas work is licence-only, without exception
Gasfitting is licensed work in NSW and there is no handyman tier of it. It is not bureaucratic caution, unburnt gas and incorrectly burnt gas are both lethal, and the second one is odourless.
It also has consequences beyond safety. Unlicensed gas work voids home insurance, invalidates appliance warranties, and surfaces during a sale. Every job here is done under licence and finishes with a certificate.
Selling, buying or leasing a property
Gas installations surface at transaction time. Buyers' inspections flag uncapped lines and old unflued heaters, insurers ask about compliance, and commercial leases usually require current certification.
A test before listing is cheap and removes a negotiating point. If you are buying an older property, having the gas installation tested before settlement is one of the better-value inspections available.
What it costs in Kellyville
Joints & fittings, $200–$600
Thread and valve leaks sealed properly and proven again on the gauge.
Pipe runs, $400–$1,500
Corroded or damaged sections replaced; concealed lines with access work run $800–$2,500.
Appliance connections, from ~$200
Connected, tested, certified. New line or bayonet to reach it quoted fixed on top.
The market rate, $120–$220/hr
Sydney's 2026 licensed-gasfitter range; attendance typically $80–$150. Certification is included, because without it there is no job.
Every gas job ends with a pressure test and the paperwork that proves it. Figures here are indicative of the 2026 Sydney market rather than a quote from us, you get your own number as a fixed price before any work starts.
Anatomy Of A Gas Job
Step 01
Step 01
Make It Safe
A suspected leak starts with isolation at the meter and ventilation, before diagnosis, before anything. No reading is worth taking on an installation still feeding a leak.
Step 02
Find It, Prove It
A manometer pressure test tells us the installation is losing gas; gas detection equipment and controlled testing narrow it to the joint, fitting or run responsible.
Step 03
Repair To Standard
The failed component or section is replaced, not doped up and hoped over, to AS/NZS 5601, whether that is one connector or a rerun line.
Step 04
Test, Relight, Certify
The whole installation holds pressure or the job is not finished. Appliances are relit and checked for correct burning, and you get the compliance side documented.
That Cooktop Won’t Connect Itself
Nor should it, legally. One visit: connected, tested, certified, warranty intact. The proper way is also the cheap way, counted honestly.
Indicatively: a pressure test and leak location $220-$450; a new bayonet or appliance point $350-$800 depending on the run; an appliance service $180-$320; a cooktop changeover $250-$500 where the point already exists. Market figures for 2026, not a quote, and every job includes the compliance certificate rather than adding it.
It is the risk with no smell and no colour, which is why a badly serviced heater is more dangerous than a leaking pipe, the leak announces itself and this does not. Soot around an appliance, condensation on windows when a heater runs, or a yellow flame all mean stop using it and book a service.
The installation is isolated, brought to a set pressure and watched on a manometer for a defined period. If the needle holds, the system is tight; if it drops, gas is escaping and the test indicates roughly how much. It is the only way to know the condition of pipework you cannot see.
Same procedure, more urgency: a leak on a shared riser affects everyone on it. Leave, take others with you, ring 131 909 from outside, then notify the building manager. Do not attempt to isolate anything in a common meter room yourself.
The supply to the building and the risers are common property; pipework and appliances inside your lot are generally yours. Individual meters may sit in a common meter room, which frequently confuses access. Establish it before arranging work, common property needs the owners corporation to authorise it.
Often, but it is rarely just plumbing. It usually needs owners corporation approval, sometimes a by-law, and always correct ventilation and flueing for the space. We will tell you what the work requires before you go to the committee, so the application you submit is the one that gets approved.
Get The Gas Done Properly In Kellyville
Licensed hands, a passing pressure test, and the certificate to prove it. Smelling gas this minute? 131 909 from outside comes before this form.
